OFM Technical Rope Rescue Practice Exam

These questions are part of the practice quiz. Start practicing

• Which term describes having multiple independent load paths beyond a single point of failure?
• What term describes a belay system that uses a separate anchor, rope, and person to manage it?
• How should rope be managed to prevent entanglement during multi-person operations?
• The standard ULC-S555-01 relates to which area of emergency services?
• In a rescue belay arrangement, which setup is operated by a person stationed below the rappeller?
• Before loading an anchor in the field, which check is recommended?
• What should be provided when rehab is required?
• If the haul team exerts a force of 200 pounds onto a 4:1 mechanical advantage system, what is the resulting force?
• How is a rope inspected?
• What does 'input force' refer to?
• What is the purpose of a backup belay line in some systems?
• What should be done with rescue equipment that has been contaminated with hazardous materials?
• What can happen if rope rubs on an edge without protection?
• What is the primary purpose of establishing incident command and a safety plan during the scene size-up?
• When rigging above an edge, what is a key precaution?
• How do you determine load distribution when rigging multiple anchors?
• In rope rescue planning, why is anchor point redundancy important?
• When should a Critical Incident Stress Debriefing begin?
• What is the name for the written document that identifies hazards within the local jurisdiction, the need for specific types of rescue capabilities, and standard operating procedures used to conduct rescue operations?
• Which standard addresses the inspection and maintenance of rescue equipment?
• How should you manage rope to prevent tangling when multiple rescuers are operating?
• What is a critical factor when selecting a pulley size for a rescue system?
• What is the primary method to ensure all crewmembers understand their responsibilities during rope rescue?
• Who is responsible for developing the Incident Action Plan?
• The descent control device primarily relies on which physical phenomenon to slow descent?
• What logic underpins the use of multiple independent anchors rather than a single strong anchor?
• What is the role of load-distributing hardware in an anchor system?
• Which NFPA standard number pertains to Life Safety Rope and Equipment for Emergency Services?
• What is the minimum breaking strength (MBS) of a general-use carabiner?
• If dynamic rope is used in a rescue and its elongation is unpredictable, what is the recommended approach?
• Which type of litter is best suited for the low angle environment?
• What is the primary purpose of a rescue briefing before operations begin?
• What is a clove hitch primarily used for in rope rescue, and what is a major caveat?
• What is the function of a Prusik in rope rescue systems?
• What is the role of a safety officer in a rope rescue incident?
• In an incident management system, which position is primarily responsible for coordinating information flow and incident action planning?
• When evaluating a near-edge rope path, what should be verified?
• Which device is used for lowering a load that may change during operations?
• What is the relationship of input and output forces in a mechanical advantage system?
• Who may conduct a system safety check?
• Which statement correctly describes the purpose of a rescue equipment log?
• In a two-person load using a figure 8 descender, how many wraps are recommended around the device?
• Using the OATH method of communication, how many rope tugs would indicate the need to eliminate slack in the rope?
• How many times would you wrap the rope around a figure 8 descender/rescue 8 for a two-person load?
• What information should you provide to paramedics?
• Which standard specifies the minimum job performance requirements for technical rescue personnel?
• Which equipment is essential to inspect regularly for rope rescue?
• What is edge protection with respect to rope movement over a lip or corner?
• When packaging a patient in a low-angle environment, which factor should be prioritized?
• What is the function of a progress capture device in a hauling system?
• Which element is essential when tying a figure-eight knot for harness attachment?
• Which type of belay system activates without any reaction from the belayer?
• Which statement about life safety rope is correct?
• Which technique describes safe patient lifting in rope rescue?
• During a rescue briefing, which element contributes to crew understanding?
• Which knot is used for webbing?
• What is a common failure mode in anchor systems that must be guarded against?
• Which statement accurately reflects edge management in rope operations?
• How do you determine the appropriate load rating of rigging hardware?
• Which item is NOT typically considered essential PPE for rope rescue operations?
• Which items are primary components of a rescue anchor system?
• When rehab is required for responders, which of the following is recommended?
• What is true about life safety rope?
• What is the minimum breaking strength of a G-rated life safety rope?
• What is the primary responsibility of the safety officer at a rope rescue incident?
• A G-rated rope's minimum breaking strength is 40 kN. Which of the following is a correct equivalent in pounds-force?
• What is the purpose of edge protection devices on an acute ascent or descent?
• Which is a clear sign that edge management is inadequate during a setup?
• What are the two main components of kernmantle rope?
• What is the belayer's response to the call of 'on rope'?
• In a hauling system, which term is typically announced when the progress capture device engages?
• What is the standard number for the NFPA Standard on Life Safety Rope and Equipment for Emergency Services?
• The litter bridle attaches to the litter at how many points?
• Which document should be consulted to understand hazards and required rescue capabilities prior to operations?
• Why is edge management critical during rope operations near edges?
• When operating near an edge, which action is prudent?
• Which statement correctly identifies the two main components of kernmantle rope?
• Who is responsible for establishing documentation methods, such as incident reports, inspection reports, and injury reports?
• For a 4:1 mechanical advantage system loaded with 200 pounds, what is the load on the rope?
• Why is a redundant anchor system important in rope rescue?
• Which description best captures a common problem caused by edge contact on rope?
• Which practice best describes redundancy in anchor selection?
• What determines the amount of energy a rope can absorb when arresting a fall?
• Which standard specifies the minimum job performance requirements for technical rescue personnel?
• Which factor is essential to evaluate about anchor points on uneven terrain before a lowering operation?
• Why is a backup knot or backup line used when rappelling or ascending?
• What is the primary consideration when choosing anchor points on varied terrain?
• Which combination of PPE is essential specifically for rope rescue operations?
• How do you verify a rope’s condition before use?
• What is the correct pounds-force equivalent of 40 kN for the G-rated rope?
• What is the typical role of a belay device in rope rescue?
• What inspection step should be performed before reusing rope?
• How is a system safety check done?
• In what situation is a safety backup line particularly important?
• What steps ensure patient stabilization when rigging a litter for lowering?
• What is the recommended practice for communicating with the crew during rope rescue?
• Ropes used for low-angle rescue operations should meet which standard?
• Which statement describes static rope's suitability for most rescue rigging?
• Which equipment type is commonly used to shield rope from sharp edges?
• Which NFPA standard number corresponds to the standard on Life Safety Rope and Equipment for Emergency Services?
• Which statement best describes a risk-benefit assessment in rope rescue operations?
• In rope rescue, what is the function of a munter hitch?
• How should you handle heat buildup during extended rope-haul operations?
• Which statement is NOT a risk of failing to manage rope near edges?
• Where is the continuous label located on life safety rope?
• Which type of belay system protects a rescuer on rappel but does not have a separate person to manage it?
• In a 3:1 system, if the load moves 50 feet upward, how many feet of rope must be pulled through?
• Using a simple 3:1 mechanical advantage system, how many feet of rope are pulled through the system to raise a person 50 feet?
• Which arrangement provides the most reliable orientation control for a haul line on uneven terrain?
• Which of the following is used to secure a litter tender's tie-in to the litter?
• In an anchor system, what is the benefit of using multiple low-stretch points rather than a single high-load point?
• What is the primary purpose of edge protection in rigging above a hazardous edge?
• What primary benefit do edge protection devices provide?
• What is the best practice for rope handling during patient lowering?
• In rope rescue, what term is used for the wheel that the rope rides over in a pulley system?
• When would you intentionally use a dynamic rope in a rope-rescue scenario?
• Which type of belay system is managed by a separate person below the rappeller?
• What harness-to-rope connection risk you must mitigate?
• Who needs to understand the accountability system at an incident?
• Which statement is true about a progress capture device (PCD)?
• What is edge protection and why is it critical in rope systems?
• What percentage range describes the stretch of a general-use life safety rope under load (1-10%)?
• Which statement about edge deflection devices is true?
• In incident management, the emergency phase ends when which condition is met?
• How much strength is lost when a nylon rope is wet?
• Which document is prepared to identify hazards within the local jurisdiction and the rescue capabilities needed before an incident?
• What does MBS stand for in rope hardware specifications?
• What is the primary outcome of applying proper edge protection during a rope rescue?
• ULC-S555-01 is a standard for which topic?
• When should a Personnel Accountability Report be conducted?
• What risk is associated with dynamic (high-stretch) rope in most rope rescue applications?
• Where will you find a continuous tape/label that identifies the date of manufacture, the lot number, and NFPA compliance?
• What is the purpose of a rescue equipment log?
• Critical Incident Stress Debriefings have which characteristic?
• Which factor describes the purpose of using a broad, redundant anchor on irregular surfaces?
• Which type of general use life safety rope stretches 1-10% at 10% of its minimum breaking strength?
• What is the function of edge protection gear in rope rescue?
• Name two common hauling/rigging configurations used to move a patient laterally or vertically.
• A black triage tag attached to a victim indicates which priority level?
• How many points of attachment are used to attach the litter bridle to the litter?
• Which belay system is one of the most popular belay systems used in the fire service?
• During packaging operations, which consideration indicates all factors are being addressed?
• Which approach best ensures safe load distribution when rigging multiple anchors?
• What type of rescue rope is described as having minimal stretch under load and is typically used as an anchor or hauling rope?
• What factor should be prioritized when selecting a pulley to minimize wear on rope?
• Which device is commonly used to create a 3:1 or 5:1 hauling system in rescue operations?
• How can rescuers prevent disease transmission?
• Which of the following is included in a system safety check for rescue equipment?
• Which IMS section is responsible for collecting, collating, and disseminating information?
• When tying a figure-eight knot for harness attachment, what is essential to ensure?
• Which device is best for lowering a load that may change during the operation?
• Which anchor method helps distribute load and provide redundancy on irregular surfaces?
• What is a common method to protect a rope when passing over a ledge or edge?
• The NFPA standard number for Life Safety Rope and Equipment for Emergency Services is what?
• What can be said about Critical Incident Stress Debriefings?
• How should you approach patient packaging on a rope-rescue if spinal injury is suspected?
• How does proper edge management influence system integrity?
• Which of the following items constitute minimum PPE for a rescuer?
• What is the purpose of using a knot or hitch to secure the rope to a carabiner?
• When is the emergency phase of an incident over for the firefighter?
• Which practice helps ensure direction control when traversing uneven terrain with a haul line?
• In a low-angle rescue environment, which litter is identified as the most suitable option?
• In a hauling system with an ascender, the arrow on the device should point toward the direction of the load. Which option represents that direction?
• What is the difference between anchor equalization and anchor redundancy?
• Which type of belay system has a separate anchor, rope, and person to manage it?
• What are the primary components of an anchor system used for rescue?
• What is the main concept of descent control devices?
• What is the primary purpose of a scene size-up in a technical rope rescue?
• Which statement is true about dynamic kernmantle rope?
• What is a key sign to check in a rope's condition that would indicate retirement from service?
• If there are two feet of a lever on one side of the fulcrum and ten feet of lever on the other side, what is the mechanical advantage?
• What is indicated by a black triage tag attached to a victim?
• What is the benefit of lowering a rescuer in a high angle rescue situation?
• Why is communications discipline critical in a rope rescue operation?
• What can be used as edge protection in rope rescue setups?
• What is the difference between a fixed pulley and a moving pulley in a rescue system?
• What is the primary danger of using damaged rope in rescue operations?
• How would you describe a proper load-testing procedure for a rescue anchor?
• Which practice helps prevent rope entanglement during multi-person operations?
• In a hauling system, what is the role of a progress-capture device?
• Which practice helps prevent rope damage when working near edges?
• Which method is used to inspect rope?
• What does a Z-drag system accomplish in rope rescue?
• What property must be considered when using a dynamic rope in rescue scenarios?
• Which of the following is a typical component evaluated during regular rope rescue equipment inspection?
• Who must give permission before you approach a helicopter?
• Nylon roping exposed to moisture loses roughly what percentage of its strength?
• In what situation would you use a rescue knot such as the alpine butterfly?
• What is meant by a “load path” in rigging?
• What is progress capture in a hauling system?
• Which factor should be considered when evaluating anchor load paths during a multi-anchor rig?
• Edge management contributes to safety by which of the following?
• Which hitch is used to secure a litter's tie-in during rescue operations?
• Which term describes distributing load among anchors to minimize single-point failure?
• The minimum breaking strength of a G-rated life safety rope is 40 kN. Which of the following is the equivalent in pounds-force?
• Which practice helps minimize rope friction at anchors or pulleys?
• Which knot is most commonly used to tie the rope to a climber’s harness for a secure connection?
• Which fastening method would you use to create a temporary anchor on a tree or irregular surface?
• What is an advantage of the tensionless hitch anchor?
• What is the advantage of a lowering system?
• If an ascender is used in a hauling system, which way should the arrow point towards?
• What is required to be provided when the SOP specifies active cooling is to be implemented?
• What is a primary technique to minimize rope damage when negotiating edges during a lowering operation?
• When is it appropriate to use a high-hands-on belay technique?
• Which of the following is recommended when rehab is required?
• How should ropes be stored when not in use to prevent degradation?
• What is the role of a safety backup line in rope work?
• Which statement best describes edge transition in rigging?